Lance,
Now that things are in the final stages any Idea what basic cost would be??
Basic populated GPIO board. (Board and SMD only)
Fully populated board with all circuits??
Thanks,
Joe-
Cost??
-
Bernard Fife
- Posts: 1696
- Joined: Fri Apr 04, 2008 1:28 pm
Re: Cost??
Joe,
I don't. I'll ask Bruce, though, he is handling the production details.
Lance.
I don't. I'll ask Bruce, though, he is handling the production details.
Lance.
"Never wrestle with pigs. You both get dirty and the pig likes it." - George Bernard Shaw
Re: Cost??
Any word yet??
Just curious mainly. Getting ready to put a 4L80E in my truck. Still have lots to do.
Thanks,
Joe
Just curious mainly. Getting ready to put a 4L80E in my truck. Still have lots to do.
Thanks,
Joe
-
Bernard Fife
- Posts: 1696
- Joined: Fri Apr 04, 2008 1:28 pm
Re: Cost??
Joe,
Sorry, I dropped the ball on this one. I will email Bruce right away and ask him to respond with his thoughts here.
Lance.
Sorry, I dropped the ball on this one. I will email Bruce right away and ask him to respond with his thoughts here.
Lance.
"Never wrestle with pigs. You both get dirty and the pig likes it." - George Bernard Shaw
-
BowlingSuperior
- Site Admin
- Posts: 5
- Joined: Fri Apr 04, 2008 12:01 pm
Re: Cost??
We have not worked out final cost for the GPIO. Probably around $160.00 or thereabouts for the PCB and connector. The ampseal is the pricey part, as is getting the harness wires sourced and crimped. Like everything else, we will try to keep this price rock-bottom as much as possible....
- Bruce
- Bruce
-
Bernard Fife
- Posts: 1696
- Joined: Fri Apr 04, 2008 1:28 pm
Re: Cost??
Thanks Bruce!
"Never wrestle with pigs. You both get dirty and the pig likes it." - George Bernard Shaw
Re: Cost??
Lance , Bruce,
Thanks for the reply. Just haven't seen any comment on price yet so I thought I would ask.
Ball park is great. Trying to plan a little and just wasn't sure if I was looking at $100 or $500.
$160 is great give or take $50 - $100
Looking forward to the release.
Joe
Thanks for the reply. Just haven't seen any comment on price yet so I thought I would ask.
Ball park is great. Trying to plan a little and just wasn't sure if I was looking at $100 or $500.
$160 is great give or take $50 - $100
Looking forward to the release.
Joe
-
dirtytorque
- Posts: 1
- Joined: Thu Feb 05, 2009 5:22 am
Re: Cost??
Hello.
Do you guys think you will release the production version this year?
Is the beta testing going well?
I'm sure u get asked this all the time but i thought i'd be cheeky and ask again.
Humbly yours
Robert.
Do you guys think you will release the production version this year?
Is the beta testing going well?
I'm sure u get asked this all the time but i thought i'd be cheeky and ask again.
Humbly yours
Robert.
-
Bernard Fife
- Posts: 1696
- Joined: Fri Apr 04, 2008 1:28 pm
Re: Cost??
Robert,
Yes, I certainly hope the production version will be released this year. Beta testing is proceeding just fine, and while there are a few changes to be made for the final boards, these are straightforward. I expect we will be able to send the final boards for production in the next month or so. Then they have to be made, built (with the SMT devices), and distributed to vendors. That could take a month or two (or possibly more if problems come up).
Lance.
Yes, I certainly hope the production version will be released this year. Beta testing is proceeding just fine, and while there are a few changes to be made for the final boards, these are straightforward. I expect we will be able to send the final boards for production in the next month or so. Then they have to be made, built (with the SMT devices), and distributed to vendors. That could take a month or two (or possibly more if problems come up).
Lance.
"Never wrestle with pigs. You both get dirty and the pig likes it." - George Bernard Shaw
Re: Cost??
Will there be boards sold without the AmpSeal? I have a non standard case and connector setup, so I would need to solder wires to the board rather than use an AmpSeal.